How to use the hand -shaped plug -in machine

Fourth, how to debug and use silicon steel sheets

warning! This item may be safe for equipment damage and safety damage. It is mainly safe during use and debugging!

4.1 The thickness of the thickness of the silicon steel sheet:
4.1.1 E.
4.1.2 Relax the front and middle gear strips. After each piece of silicon steel sheet is placed, the plug ruler is placed on the silicon steel sheet (corresponding to 0.5mm pluggage ruler thickness is 0.15mm, and 0.3mm tablets are as a tablet. 0.10mm) The segiarbon can be premored.
4.1.3 Press the barrier on the plug slide to move left and right, respectively, and then remove the ruler after the screw is locked.
4.2 How to use
4.2.1, put the E and I silicon steel sheets in the left and right lower material board, and the hair edges up to reduce the wear of the silicon steel sheet to the machine parts Press the iron block to press the silicon steel sheet to prevent the phenomenon of turning the film or not producing).
4.2.2, the left hand holds the top of the line, put half of its thickness into the sliding guide in the plug -in machine, and insert two pieces of EI films at the bottom of the online package (note: the hair surface is upward, so as to go down, so as to use it to go down, so as to use it to go down, so as to use it to go down, so as to use it to go down, so as to use it to go down, so as to use it. Reduce the friction of the medium -sized slippery and the surface of the upper skirting), and at the same time make the steel sheet at the bottom of the wires in the horizontal contact with the skid guidance, the bottom plastic horizontal contact on the plane of the mobile phone, the right hand holds the handle of the handle, lightly press the wire bag When starting slowly at 3-5 pieces, two excess i films are pushed out of the top of the silicon steel sheet. Insert the wire bag), slightly shake the wire bag with your left hand, shake the right hand until it is full.
4.2.3, please keep exercise at a constant speed when working.

4.3 Machine maintenance and use precautions
4.3.1, cannot be squeezed or knocking machine with heavy objects to prevent the machine deformation and loosening due to external forces, causing the machine to fail to cause a failure of the machine. Essence
4.3.2, the fastening screws on the machine and all the adjustment screws, please do not disassemble at will, and regularly check whether the fastener screws are loose.
4.3.3, the machine sliding part of the machine needs to be frequent rust oil (WD-40) to keep the whole machine lubricating.
4.3.4. When the machine works, no other physical objects are allowed to enter the body except the silicon steel sheet (especially the hand!).

. Frequent failure causes and corresponding treatment methods

. The porn is diagonal:
1, the gap between the front block is different – – – – Loose the front block and adjust it appropriately.
2, the high height of the film is different – – – – – — -when the front and rear material boards are removed, and then the card iron is promoted to about 1-2mm in the I negative, and one E film is taken to put it vertically on it vertically on it. Above the card iron, use 0.3mm thick plug ruler to measure whether the card iron and the bottom of the bottom of the I have 0.3mm. Paper.
3, the card iron skew- -relax the card iron screw, use the piece between the side plate and the card iron, and then the card iron is 90 degrees of right angle, and finally the card iron is locked.
4, the contact surface of the hook film and the I negatives is not a plane (this situation is usually for a long time after the machine works, it appears due to the wear of the machine) – – — to the school.
5, the tightness of the two hook pieces is different – – – -adjust the fixed screws on the hook tablet, so that the two hooks are equal to the pressure.
6, the front gear gap is not available (the distance is the distance from the surface on the top of I) – -adjust the mid -block gap.
. Can’t push out:
1, the height of the card iron – – The paper with the corresponding thickness on the floor plane of the card iron bottom.
2, the decline of the guidance screw loose (cause the active board to fall down) — tighten the sliding down the guidance screw.
three, E pour back:
1, the pressure of the hook pieces is not enough hook tablet pressure, the front surface of the hook film and the surface of the upper skate guide after a long time of work friction, — cause the pressure when the E -film is launched, pressure If you can’t stop it, you will bring the E -film back when the card iron returns. This phenomenon needs to be replaced with a new spring.
2, after the card iron is worn, when pushing the E -film, it will cause the E film to not push it under the hook tablet. -This of this phenomenon needs to be dismantled and raised, so that the card iron can smoothly push the E -piece to the hook.
CBMace-dedicated to electronic transformer system solutions!